![]() Affected 2007 Accord V6 only: Reinstall the timing belt adjuster.ġ5. Affected 2007 Accord V6 only: Replace the water pump, and reuse the coolant you removed in step 1.ġ4. Using a die grinder with a 2-in., 50-grit grinding disc (or equivalent) and the circular casting offset as a guide, grind the side engine mount bracket until the lip measures 2 mm thick with a caliper or micrometer ( see Fig. If the feeler gauge did not fit in step 5, remove the side engine mount bracket. If the feeler gauge did fit in step 5, go to step 13. Affected 2007 Accord V6 only: Remove the water pump.ġ2. Affected 2007 Accord V6 only: Remove the timing belt adjuster.ġ0. Do not disconnect the CKP harness connector.ĩ. Unbolt the CKP (crankshaft position) sensor (if applicable), and set it aside. Note: Remove the feeler gauge from its holder to get a more accurate measurement.Ħ. This measurement is used to determine if step 12 is required ( see Fig. Try to insert a 0.95 mm feeler gauge between the top edge of the timing belt idler pulley and the back of the side engine mount bracket overhanging the pulley. Set the engine to TDC (top dead center).ģ. Affected 2007 Accord V6 only: Drain the engine coolant into a clean container, and save it for reuse.Ģ. All other non-water pump replacement steps apply to all affected vehicles.ġ. Note: On certain 2007 Accord V6 vehicles, you will also be replacing the water pump (see Corrective Action). Make sure there is no more noise coming from the accessory drive belt before proceeding. No – Reinstall the drive belt, and then continue with normal accessory drive belt troubleshooting procedures. Do you still hear the noise? Yes – Go to Repair Procedure. Shut off the engine and remove the accessory drive belt.ģ. Confirm the noise present at idle with a warm engine.Ģ. 2006-’08 models: P/N 04148-RCA-306 (Contains taper shim, timing belt and timing belt drive pulley gear) Water Pump (2007 Accord V6 only): P/N 19200-RDM-A02 Hondalock 1 (or equivalent): (one container repairs about 10 vehicles): P/N 08713-0001ġ. ![]() 4-Door with M/T – From VIN 1HGCM6 …7A034807 through 1HGCM6…7A057992Īpplicable Models: 2005-’08 Accord V6, Odyssey and Pilot, and 2006-’08 Ridgeline Required Parts and Materials:.These 2007 Accord V6 vehicles also require water pump replacement: Install the lower cover and crankshaft pulley.Install a taper shim kit, and grind a deeper relief on the engine mount bracket, if needed. If you have a timing belt guide plate, install it with the concave surface facing out. Install the engine mount bracket to the front of engine. Next, remove the retaining tool or pin from the auto-tensioner. ![]() With the belt in place, tighten the idler pulley bolt to 38 ft.-lbs.ġ3. To aid in this process, we use spring-loaded clips to hold the belts on the pulleys as the belt is routed. Note: Be sure the crankshaft and camshaft pulleys remained aligned with the marks on the back cover. When it comes time to install the timing belt, reinstall the tensioner with the pin or stopper tool in place, loosely install the idler pulley using thread locker, and then install the timing belt in a counterclockwise direction following this sequence: Crankshaft pulley, idler pulley, front camshaft pulley, water pump pulley, rear camshaft pulley and tension adjust pulley. An unopened witch’s hat from a bottle of gear oil or tube of silicone will do the job.ġ2. Either temporarily install the tube or find a plug that will do the job. Before you do, don’t forget that you removed the dipstick tube, so if you didn’t seal the hole before, now is the time to be sure you don’t allow coolant to enter the crankcase. With the belt removed, you can now remove the fasteners and replace the water pump.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |